102 lines
3.4 KiB
Text
102 lines
3.4 KiB
Text
#
|
|
# Sample configuration file for TAYGA 0.9.2
|
|
#
|
|
# Modify this to use your own addresses!!
|
|
#
|
|
|
|
#
|
|
# TUN device that TAYGA will use to exchange IPv4 and IPv6 packets with the
|
|
# kernel. You may use any name you like, but `nat64' is recommended.
|
|
#
|
|
# This device may be created before starting the tayga daemon by running
|
|
# `tayga --mktun`. This allows routing and firewall rules to be set up prior
|
|
# to commencement of packet translation.
|
|
#
|
|
# Mandatory.
|
|
#
|
|
tun-device nat64
|
|
|
|
#
|
|
# TAYGA's IPv4 address. This is NOT your router's IPv4 address! TAYGA
|
|
# requires its own address because it acts as an IPv4 and IPv6 router, and
|
|
# needs to be able to send ICMP messages. TAYGA will also respond to ICMP
|
|
# echo requests (ping) at this address.
|
|
#
|
|
# This address can safely be located inside the dynamic-pool prefix.
|
|
#
|
|
# Mandatory.
|
|
#
|
|
ipv4-addr 192.168.255.1
|
|
|
|
#
|
|
# TAYGA's IPv6 address. This is NOT your router's IPv6 address! TAYGA
|
|
# requires its own address because it acts as an IPv4 and IPv6 router, and
|
|
# needs to be able to send ICMP messages. TAYGA will also respond to ICMP
|
|
# echo requests (ping6) at this address.
|
|
#
|
|
# You can leave ipv6-addr unspecified and TAYGA will construct its IPv6
|
|
# address using ipv4-addr and the NAT64 prefix.
|
|
#
|
|
# Optional if the NAT64 prefix is specified, otherwise mandatory. It is also
|
|
# mandatory if the NAT64 prefix is 64:ff9b::/96 and ipv4-addr is a private
|
|
# (RFC1918) address.
|
|
#
|
|
#ipv6-addr 2001:db8:1::2
|
|
|
|
#
|
|
# The NAT64 prefix. The IPv4 address space is mapped into the IPv6 address
|
|
# space by prepending this prefix to the IPv4 address. Using a /96 prefix is
|
|
# recommended in most situations, but all lengths specified in RFC 6052 are
|
|
# supported.
|
|
#
|
|
# This must be a prefix selected from your organization's IPv6 address space
|
|
# or the Well-Known Prefix 64:ff9b::/96. Note that using the Well-Known
|
|
# Prefix will prohibit IPv6 hosts from contacting IPv4 hosts that have private
|
|
# (RFC1918) addresses, per RFC 6052.
|
|
#
|
|
# The NAT64 prefix need not be specified if all required address mappings are
|
|
# listed in `map' directives. (See below.)
|
|
#
|
|
# Optional.
|
|
#
|
|
prefix 2001:db8:1:ffff::/96
|
|
# prefix 64:ff9b::/96
|
|
|
|
#
|
|
# Dynamic pool prefix. IPv6 hosts which send traffic through TAYGA (and do
|
|
# not correspond to a static map or an IPv4-translatable address in the NAT64
|
|
# prefix) will be assigned an IPv4 address from the dynamic pool. Dynamic
|
|
# maps are valid for 124 minutes after the last matching packet is seen.
|
|
#
|
|
# If no unassigned addresses remain in the dynamic pool (or no dynamic pool is
|
|
# configured), packets from unknown IPv6 hosts will be rejected with an ICMP
|
|
# unreachable error.
|
|
#
|
|
# Optional.
|
|
#
|
|
dynamic-pool 192.168.255.0/24
|
|
|
|
#
|
|
# Persistent data storage directory. The dynamic.map file, which saves the
|
|
# dynamic maps that are created from dynamic-pool, is stored in this
|
|
# directory. Omit if you do not need these maps to be persistent between
|
|
# instances of TAYGA.
|
|
#
|
|
# Optional.
|
|
#
|
|
data-dir /var/db/tayga
|
|
|
|
#
|
|
# Establishes a single-host map. If an IPv6 host should be consistently
|
|
# reachable at a specific IPv4 address, the mapping can be specified in a
|
|
# `map' directive. (IPv6 hosts numbered with an IPv4-translatable address do
|
|
# not need map directives.)
|
|
#
|
|
# IPv4 addresses specified in the `map' directive can safely be located inside
|
|
# the dynamic-pool prefix.
|
|
#
|
|
# Optional.
|
|
#
|
|
#map 192.168.5.42 2001:db8:1:4444::1
|
|
#map 192.168.5.43 2001:db8:1:4444::2
|
|
#map 192.168.255.2 2001:db8:1:569::143
|