From 012c8b9a1cab46332d87a9b132c88e80b05144cb Mon Sep 17 00:00:00 2001
From: Nico Schottelius <nico@wurzel.schottelius.org>
Date: Sun, 18 Sep 2016 09:25:44 +0200
Subject: [PATCH] remove code we do not use

Signed-off-by: Nico Schottelius <nico@wurzel.schottelius.org>
---
 HackZurich_LoraWan.ino | 119 -----------------------------------------
 1 file changed, 119 deletions(-)
 delete mode 100644 HackZurich_LoraWan.ino

diff --git a/HackZurich_LoraWan.ino b/HackZurich_LoraWan.ino
deleted file mode 100644
index 9560729..0000000
--- a/HackZurich_LoraWan.ino
+++ /dev/null
@@ -1,119 +0,0 @@
-#include "Sodaq_RN2483.h"
-#include "Arduino.h"
-
-#define debugSerial SerialUSB
-#define loraSerial Serial1
-
-
-
-void RED() {
-  digitalWrite(LED_RED, LOW);
-  digitalWrite(LED_GREEN, HIGH);
-  digitalWrite(LED_BLUE, HIGH);
-}
-
-void CLEAR() {
-  digitalWrite(LED_RED, HIGH);
-  digitalWrite(LED_GREEN, HIGH);
-  digitalWrite(LED_BLUE, HIGH);
-}
-
-// OTAA
-​// I took 0x02 here as device Id...
-uint8_t DevEUI[8] = { 0x9c, 0xd9, 0x0b, 0xb5, 0x2b, 0x6a, 0x1d, 0x02 };
-uint8_t AppEUI[8] = { 0xd4, 0x16, 0xcd, 0x0b, 0x7b, 0xcf, 0x2d, 0x5c };
-uint8_t AppKey[16] = {0xa9, 0xbc, 0x8b, 0x6a, 0x81, 0x75, 0xf6, 0x33,
-0xe0, 0xd6, 0x64, 0xd9, 0x2b, 0xcb, 0x13, 0x78 };
-
-void setupLoRaOTAA(){
-  if (LoRaBee.initOTA(loraSerial, DevEUI, AppEUI, AppKey, true))
-  {
-    debugSerial.println("Communication to LoRaBEE successful.");
-  }
-  else
-  {
-    debugSerial.println("OTAA Setup failed!");
-  }
-}
-
-void setup() {
-  //Power up the LoRaBEE
-  pinMode(ENABLE_PIN_IO, OUTPUT); // ONE
-  digitalWrite(ENABLE_PIN_IO, HIGH); // ONE
-  pinMode(LED_RED, OUTPUT);
-  pinMode(LED_GREEN, OUTPUT);
-  pinMode(LED_BLUE, OUTPUT);
-  delay(3000);
-
-  while ((!SerialUSB) && (millis() < 10000)){
-    // Wait 10 seconds for the Serial Monitor
-  }
-
-  //Set baud rate
-  debugSerial.begin(57600);
-  loraSerial.begin(LoRaBee.getDefaultBaudRate());
-
-  // Debug output from LoRaBee
-  // LoRaBee.setDiag(debugSerial); // optional
-
-  //connect to the LoRa Network
-  setupLoRa();
-}
-
-void setupLoRa(){
-  // ABP
-//  setupLoRaABP();
-  // OTAA
-  setupLoRaOTAA();
-}
-
-void sendPacket(String packet){
-  switch (LoRaBee.sendReqAck(1, (uint8_t*)packet.c_str(), packet.length(), 8))
-    {
-    case NoError:
-      debugSerial.println("Successful transmission.");
-      break;
-    case NoResponse:
-      debugSerial.println("There was no response from the device.");
-      setupLoRa();
-      break;
-    case Timeout:
-      debugSerial.println("Connection timed-out. Check your serial connection to the device! Sleeping for 20sec.");
-      delay(20000);
-      break;
-    case PayloadSizeError:
-      debugSerial.println("The size of the payload is greater than allowed. Transmission failed!");
-      break;
-    case InternalError:
-      debugSerial.println("Oh No! This shouldn't happen. Something is really wrong! Try restarting the device!\r\nThe network connection will reset.");
-      setupLoRa();
-      break;
-    case Busy:
-      debugSerial.println("The device is busy. Sleeping for 10 extra seconds.");
-      delay(10000);
-      break;
-    case NetworkFatalError:
-      debugSerial.println("There is a non-recoverable error with the network connection. You should re-connect.\r\nThe network connection will reset.");
-      setupLoRa();
-      break;
-    case NotConnected:
-      debugSerial.println("The device is not connected to the network. Please connect to the network before attempting to send data.\r\nThe network connection will reset.");
-      setupLoRa();
-      break;
-    case NoAcknowledgment:
-      debugSerial.println("There was no acknowledgment sent back!");
-      // When you this message you are probaly out of range of the network.
-      break;
-    default:
-      break;
-    }
-}
-
-void loop() {
-  // put your main code here, to run repeatedly:
-  String packet = "SODAQ";
-  sendPacket(packet);
-RED();
-  delay(5000);
-  CLEAR();
-}