112 lines
3.0 KiB
C++
112 lines
3.0 KiB
C++
#include <Arduino.h>
|
|
#include "Sodaq_RN2483.h"
|
|
#include "internal.h"
|
|
|
|
#define loraSerial Serial1
|
|
#define beePin ENABLE_PIN_IO
|
|
|
|
#ifdef LORA_ABP
|
|
void setupLoRaABP(){
|
|
if (LoRaBee.initABP(loraSerial, devAddr, appSKey, nwkSKey, true))
|
|
{
|
|
debugSerial.println("Lora: ABP setup ok");
|
|
}
|
|
else
|
|
{
|
|
debugSerial.println("Lora: ABP setup failed");
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#ifdef LORA_OTAA
|
|
void setupLoRaOTAA(){
|
|
if (LoRaBee.initOTA(loraSerial, DevEUI, AppEUI, AppKey, true))
|
|
{
|
|
debugSerial.println("Lora: OTAA setup ok");
|
|
}
|
|
else
|
|
{
|
|
debugSerial.println("Lora: OTAA Setup failed!");
|
|
}
|
|
}
|
|
#endif
|
|
|
|
|
|
void loraSetup()
|
|
{
|
|
pinMode(beePin, OUTPUT); // ONE
|
|
digitalWrite(beePin, HIGH); // Lorawan
|
|
loraSerial.begin(LoRaBee.getDefaultBaudRate());
|
|
|
|
#ifdef LORA_OTAA
|
|
setupLoRaOTAA();
|
|
#endif
|
|
|
|
#ifdef LORA_ABP
|
|
setupLoRaABP();
|
|
#endif
|
|
}
|
|
|
|
void loraSend(String packet){
|
|
debugSerial.println("Trying to send: " + packet);
|
|
led_on();
|
|
|
|
/* with ack */
|
|
//switch (LoRaBee.sendReqAck(1, (uint8_t*)packet.c_str(), packet.length(), 8))
|
|
switch (LoRaBee.send(1, (uint8_t*)packet.c_str(), packet.length()) )
|
|
{
|
|
case NoError:
|
|
debugSerial.println("Successful transmission.");
|
|
break;
|
|
case NoResponse:
|
|
debugSerial.println("There was no response from the device.");
|
|
loraSetup();
|
|
break;
|
|
case Timeout:
|
|
debugSerial.println("Connection timed-out. Check your serial connection to the device! Sleeping for 20sec.");
|
|
delay(20000);
|
|
break;
|
|
case PayloadSizeError:
|
|
debugSerial.println("The size of the payload is greater than allowed. Transmission failed!");
|
|
break;
|
|
case InternalError:
|
|
debugSerial.println("Oh No! This shouldn't happen. Something is really wrong! Try restarting the device!\r\nThe network connection will reset.");
|
|
loraSetup();
|
|
break;
|
|
case Busy:
|
|
debugSerial.println("The device is busy. Sleeping for 10 extra seconds.");
|
|
delay(10000);
|
|
break;
|
|
case NetworkFatalError:
|
|
debugSerial.println("There is a non-recoverable error with the network connection. You should re-connect.\r\nThe network connection will reset.");
|
|
loraSetup();
|
|
break;
|
|
case NotConnected:
|
|
debugSerial.println("The device is not connected to the network. Please connect to the network before attempting to send data.\r\nThe network connection will reset.");
|
|
loraSetup();
|
|
break;
|
|
case NoAcknowledgment:
|
|
debugSerial.println("There was no acknowledgment sent back!");
|
|
// When you this message you are probaly out of range of the network.
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
/* Delay some time to give avoid keeping the device busy */
|
|
delay(2000);
|
|
led_off();
|
|
}
|
|
|
|
void sendIntAsString(String prefix, int value) {
|
|
String tmp = prefix + String(value);
|
|
debugSerial.println(tmp);
|
|
loraSend(tmp);
|
|
}
|
|
|
|
void sendFloatAsString(String prefix, float value) {
|
|
String tmp = prefix + String(value);
|
|
debugSerial.println(tmp);
|
|
loraSend(tmp);
|
|
}
|