lorawan/HackZurich_LoraWan.ino
2016-09-14 20:02:05 +02:00

119 lines
3.2 KiB
C++
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

#include "Sodaq_RN2483.h"
#include "Arduino.h"
#define debugSerial SerialUSB
#define loraSerial Serial1
void RED() {
digitalWrite(LED_RED, LOW);
digitalWrite(LED_GREEN, HIGH);
digitalWrite(LED_BLUE, HIGH);
}
void CLEAR() {
digitalWrite(LED_RED, HIGH);
digitalWrite(LED_GREEN, HIGH);
digitalWrite(LED_BLUE, HIGH);
}
// OTAA
// I took 0x02 here as device Id...
uint8_t DevEUI[8] = { 0x9c, 0xd9, 0x0b, 0xb5, 0x2b, 0x6a, 0x1d, 0x02 };
uint8_t AppEUI[8] = { 0xd4, 0x16, 0xcd, 0x0b, 0x7b, 0xcf, 0x2d, 0x5c };
uint8_t AppKey[16] = {0xa9, 0xbc, 0x8b, 0x6a, 0x81, 0x75, 0xf6, 0x33,
0xe0, 0xd6, 0x64, 0xd9, 0x2b, 0xcb, 0x13, 0x78 };
void setupLoRaOTAA(){
if (LoRaBee.initOTA(loraSerial, DevEUI, AppEUI, AppKey, true))
{
debugSerial.println("Communication to LoRaBEE successful.");
}
else
{
debugSerial.println("OTAA Setup failed!");
}
}
void setup() {
//Power up the LoRaBEE
pinMode(ENABLE_PIN_IO, OUTPUT); // ONE
digitalWrite(ENABLE_PIN_IO, HIGH); // ONE
pinMode(LED_RED, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_BLUE, OUTPUT);
delay(3000);
while ((!SerialUSB) && (millis() < 10000)){
// Wait 10 seconds for the Serial Monitor
}
//Set baud rate
debugSerial.begin(57600);
loraSerial.begin(LoRaBee.getDefaultBaudRate());
// Debug output from LoRaBee
// LoRaBee.setDiag(debugSerial); // optional
//connect to the LoRa Network
setupLoRa();
}
void setupLoRa(){
// ABP
// setupLoRaABP();
// OTAA
setupLoRaOTAA();
}
void sendPacket(String packet){
switch (LoRaBee.sendReqAck(1, (uint8_t*)packet.c_str(), packet.length(), 8))
{
case NoError:
debugSerial.println("Successful transmission.");
break;
case NoResponse:
debugSerial.println("There was no response from the device.");
setupLoRa();
break;
case Timeout:
debugSerial.println("Connection timed-out. Check your serial connection to the device! Sleeping for 20sec.");
delay(20000);
break;
case PayloadSizeError:
debugSerial.println("The size of the payload is greater than allowed. Transmission failed!");
break;
case InternalError:
debugSerial.println("Oh No! This shouldn't happen. Something is really wrong! Try restarting the device!\r\nThe network connection will reset.");
setupLoRa();
break;
case Busy:
debugSerial.println("The device is busy. Sleeping for 10 extra seconds.");
delay(10000);
break;
case NetworkFatalError:
debugSerial.println("There is a non-recoverable error with the network connection. You should re-connect.\r\nThe network connection will reset.");
setupLoRa();
break;
case NotConnected:
debugSerial.println("The device is not connected to the network. Please connect to the network before attempting to send data.\r\nThe network connection will reset.");
setupLoRa();
break;
case NoAcknowledgment:
debugSerial.println("There was no acknowledgment sent back!");
// When you this message you are probaly out of range of the network.
break;
default:
break;
}
}
void loop() {
// put your main code here, to run repeatedly:
String packet = "SODAQ";
sendPacket(packet);
RED();
delay(5000);
CLEAR();
}