361 lines
7.2 KiB
C++
361 lines
7.2 KiB
C++
#include "Sodaq_RN2483.h"
|
|
#include "Arduino.h"
|
|
|
|
|
|
#define debugSerial SerialUSB
|
|
#define loraSerial Serial1
|
|
|
|
/* The number of the device: 1,2,3,4 */
|
|
#define deviceNo 2
|
|
|
|
#define beePin ENABLE_PIN_IO
|
|
|
|
#define LOUDNESS_SENSOR 0
|
|
#define LIGHT_SENSOR 2
|
|
#define WATER_SENSOR 6
|
|
#define BUZZER 8
|
|
#define MAGNETIC_SWITCH 12
|
|
#define TEMPERATURE 13
|
|
|
|
int loudness;
|
|
|
|
void BLUE() {
|
|
digitalWrite(LED_RED, HIGH);
|
|
digitalWrite(LED_GREEN, HIGH);
|
|
digitalWrite(LED_BLUE, LOW);
|
|
}
|
|
|
|
void RED() {
|
|
digitalWrite(LED_RED, LOW);
|
|
digitalWrite(LED_GREEN, HIGH);
|
|
digitalWrite(LED_BLUE, HIGH);
|
|
}
|
|
|
|
void YELLOW() {
|
|
digitalWrite(LED_RED, LOW);
|
|
digitalWrite(LED_GREEN, LOW);
|
|
digitalWrite(LED_BLUE, HIGH);
|
|
}
|
|
|
|
void WHITE() {
|
|
digitalWrite(LED_RED, LOW);
|
|
digitalWrite(LED_GREEN, LOW);
|
|
digitalWrite(LED_BLUE, LOW);
|
|
}
|
|
|
|
|
|
void GREEN() {
|
|
digitalWrite(LED_RED, HIGH);
|
|
digitalWrite(LED_GREEN, LOW);
|
|
digitalWrite(LED_BLUE, HIGH);
|
|
}
|
|
|
|
void CLEAR() {
|
|
digitalWrite(LED_RED, HIGH);
|
|
digitalWrite(LED_GREEN, HIGH);
|
|
digitalWrite(LED_BLUE, HIGH);
|
|
}
|
|
|
|
void blink(int length) {
|
|
switch(deviceNo) {
|
|
case 1:
|
|
BLUE();
|
|
break;
|
|
case 2:
|
|
RED();
|
|
break;
|
|
case 3:
|
|
GREEN();
|
|
break;
|
|
case 4:
|
|
WHITE();
|
|
break;
|
|
}
|
|
delay(length);
|
|
CLEAR();
|
|
}
|
|
|
|
void beep(int howlong) {
|
|
buzzOn();
|
|
delay(howlong);
|
|
buzzOff();
|
|
}
|
|
|
|
void buzzOn() {
|
|
digitalWrite(BUZZER, HIGH);
|
|
}
|
|
|
|
void buzzOff() {
|
|
digitalWrite(BUZZER, LOW);
|
|
}
|
|
|
|
|
|
void setupLED() {
|
|
pinMode(LED_RED, OUTPUT);
|
|
pinMode(LED_GREEN, OUTPUT);
|
|
pinMode(LED_BLUE, OUTPUT);
|
|
}
|
|
|
|
|
|
|
|
uint8_t DevEUI[8] = { 0x9c, 0xd9, 0x0b, 0xb5, 0x2b, 0x6a, 0x1d, deviceNo };
|
|
|
|
// TTN
|
|
uint8_t AppEUI[8] = { 0x70, 0xB3, 0xD5, 0x7E, 0xD0, 0x00, 0x0E, 0x9e };
|
|
|
|
|
|
// F1B165CF06B156B0BB6970FC209602EA
|
|
uint8_t AppKey[16] = { 0xF1, 0xB1, 0x65, 0xCF,
|
|
0x06, 0xB1, 0x56, 0xB0, 0xBB,
|
|
0x69, 0x70, 0xFC, 0x20, 0x96,
|
|
0x02, 0xEA };
|
|
|
|
uint8_t counter;
|
|
|
|
void setupLoRaOTAA(){
|
|
if (LoRaBee.initOTA(loraSerial, DevEUI, AppEUI, AppKey, true))
|
|
{
|
|
debugSerial.println("Communication to LoRaBEE successful.");
|
|
}
|
|
else
|
|
{
|
|
debugSerial.println("OTAA Setup failed!");
|
|
}
|
|
}
|
|
|
|
|
|
int setupLoudness()
|
|
{
|
|
loudness = 0;
|
|
// pinMode(LOUDNESS_SENSOR, INPUT);
|
|
}
|
|
|
|
int readLoudness()
|
|
{
|
|
return analogRead(LOUDNESS_SENSOR);
|
|
}
|
|
|
|
int readLight()
|
|
{
|
|
int sensorValue = analogRead(LIGHT_SENSOR);
|
|
return map(sensorValue, 11, 27333, 0, 413);
|
|
}
|
|
|
|
void setupWater() {
|
|
pinMode(WATER_SENSOR, INPUT);
|
|
}
|
|
|
|
boolean hasWater()
|
|
{
|
|
if(digitalRead(WATER_SENSOR) == LOW) {
|
|
return true;
|
|
} else {
|
|
return false;
|
|
}
|
|
}
|
|
|
|
void setupTemp() {
|
|
pinMode(TEMPERATURE, INPUT);
|
|
}
|
|
|
|
float readTemp()
|
|
{
|
|
float temperature;
|
|
int B=4250; //B value of the thermistor
|
|
float resistance;
|
|
int a;
|
|
|
|
a=analogRead(TEMPERATURE);
|
|
resistance=(float)(1023-a)*10000/a; //get the resistance of the sensor;
|
|
temperature=1/(log(resistance/10000)/B+1/298.15)-273.15;//convert to temperature via datasheet ;
|
|
|
|
return temperature;
|
|
}
|
|
|
|
|
|
void setupBuzzer()
|
|
{
|
|
pinMode(BUZZER, OUTPUT);
|
|
}
|
|
|
|
|
|
void setupMagnet()
|
|
{
|
|
pinMode(MAGNETIC_SWITCH, INPUT);
|
|
}
|
|
|
|
boolean isMagnetic()
|
|
{
|
|
if(digitalRead(MAGNETIC_SWITCH) == HIGH)
|
|
return true;
|
|
else
|
|
return false;
|
|
}
|
|
|
|
|
|
|
|
void setup() {
|
|
//Power up the LoRaBEE - on loraone/sodaq one
|
|
pinMode(ENABLE_PIN_IO, OUTPUT); // ONE
|
|
|
|
digitalWrite(beePin, HIGH); // ONE
|
|
delay(3000);
|
|
|
|
/* Enable the pins 2/3, 6/7 and 8/9 */
|
|
pinMode(11, OUTPUT);
|
|
digitalWrite(11, HIGH);
|
|
|
|
while ((!SerialUSB) && (millis() < 10000)){
|
|
// Wait 10 seconds for the Serial Monitor
|
|
}
|
|
|
|
//Set baud rate
|
|
debugSerial.begin(57600);
|
|
loraSerial.begin(LoRaBee.getDefaultBaudRate());
|
|
|
|
// Debug output from LoRaBee
|
|
// LoRaBee.setDiag(debugSerial); // optional
|
|
|
|
setupLED();
|
|
blink(60);
|
|
|
|
/* used for blinking */
|
|
counter=0;
|
|
setupLoudness();
|
|
|
|
//connect to the LoRa Network
|
|
setupLoRa();
|
|
|
|
/* setupWater();
|
|
setupBuzzer();
|
|
setupMagnet(); */
|
|
|
|
}
|
|
|
|
void setupLoRa(){
|
|
setupLoRaOTAA();
|
|
}
|
|
|
|
void sendPacket(String packet){
|
|
switch (LoRaBee.sendReqAck(1, (uint8_t*)packet.c_str(), packet.length(), 8))
|
|
{
|
|
case NoError:
|
|
debugSerial.println("Successful transmission.");
|
|
break;
|
|
case NoResponse:
|
|
debugSerial.println("There was no response from the device.");
|
|
setupLoRa();
|
|
break;
|
|
case Timeout:
|
|
debugSerial.println("Connection timed-out. Check your serial connection to the device! Sleeping for 20sec.");
|
|
delay(20000);
|
|
break;
|
|
case PayloadSizeError:
|
|
debugSerial.println("The size of the payload is greater than allowed. Transmission failed!");
|
|
break;
|
|
case InternalError:
|
|
debugSerial.println("Oh No! This shouldn't happen. Something is really wrong! Try restarting the device!\r\nThe network connection will reset.");
|
|
setupLoRa();
|
|
break;
|
|
case Busy:
|
|
debugSerial.println("The device is busy. Sleeping for 10 extra seconds.");
|
|
delay(10000);
|
|
break;
|
|
case NetworkFatalError:
|
|
debugSerial.println("There is a non-recoverable error with the network connection. You should re-connect.\r\nThe network connection will reset.");
|
|
setupLoRa();
|
|
break;
|
|
case NotConnected:
|
|
debugSerial.println("The device is not connected to the network. Please connect to the network before attempting to send data.\r\nThe network connection will reset.");
|
|
setupLoRa();
|
|
break;
|
|
case NoAcknowledgment:
|
|
debugSerial.println("There was no acknowledgment sent back!");
|
|
// When you this message you are probaly out of range of the network.
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
void loop() {
|
|
|
|
|
|
/* Announce begin of code */
|
|
blink(20); delay(50);
|
|
blink(20); delay(50);
|
|
blink(20); delay(50);
|
|
|
|
loudness = readLoudness();
|
|
|
|
String data_loudness = String("loudness=" + String(loudness, DEC));
|
|
debugSerial.println(data_loudness);
|
|
|
|
/* String data_light = String("light=" + String(readLight(), 3));
|
|
debugSerial.println(data_light); */
|
|
|
|
/* String data_temp = String("temp=" + String(readTemp(), 3));
|
|
debugSerial.println(data_temp);*/
|
|
|
|
|
|
/*
|
|
String data_water;
|
|
if(hasWater()) {
|
|
data_water = String("water=1");
|
|
buzzOn();
|
|
} else {
|
|
data_water = String("water=0");
|
|
buzzOff();
|
|
}
|
|
debugSerial.println(data_water);
|
|
|
|
String data_magnet;
|
|
if(isMagnetic()) {
|
|
data_magnet = String("magnet=1");
|
|
} else {
|
|
data_magnet = String("magnet=0");
|
|
}
|
|
debugSerial.println(data_magnet);
|
|
|
|
*/
|
|
|
|
int wait = 10000;
|
|
|
|
debugSerial.println(String("wait=" + String(wait)));
|
|
sendPacket(data_loudness);
|
|
blink(20); delay(wait);
|
|
|
|
|
|
/*sendPacket(data_temp);
|
|
blink(20); delay(2980);
|
|
sendPacket(data_light);
|
|
blink(20); delay(2980);
|
|
sendPacket(data_water);
|
|
blink(20); delay(2980);
|
|
sendPacket(data_magnet);*/
|
|
|
|
|
|
/* Blink long after sending packet
|
|
if(counter >= 10) {
|
|
// Beep(20);
|
|
blink(20);
|
|
delay(10);
|
|
blink(20);
|
|
sendPacket(data_temp);
|
|
blink(500);
|
|
sendPacket(data_loudness);
|
|
blink(500);
|
|
sendPacket(data_light);
|
|
blink(500);
|
|
sendPacket(data_water);
|
|
blink(500);
|
|
sendPacket(data_magnet);
|
|
counter = 0;
|
|
} else {
|
|
blink(30);
|
|
counter++;
|
|
}
|
|
*/
|
|
|
|
// delay(1000);
|
|
}
|